What does FANUC alarm 431 mean?
FANUC Alarm 431 is related to the converter or the power supply section of the servo system. In the FANUC Series 0i Model C maintenance manual, its description is:
431 – n AXIS: CNV. OVERLOAD
The manual identifies two possible conditions:
- PSM: Overheat occurred.
- β-series SVU: overheat.
For certain PSM models the corresponding internal Alarm Code 03 indicates that the main circuit heat sink temperature has become abnormally high.
It's vital not to confuse Alarm 431 with Alarm 430 (which is servo motor overheat). They're different alarms relating to different components and will require different approaches to diagnosis and rectification.
Common Causes of FANUC Alarm 431
The principal possible causes are going to be down to the power supply or servo unit that's in use.
1. Cooling Fan Failure
A damaged or non-operating cooling fan will lead to reduced heat dissipation from within the power module and as such the internal temperature can rise well above the normal operating range.
Check that the cooling fan is turning freely and that the connections are all in order.
2. Dust Accumulation on the Heat Sink
Dust and other contamination can build up on the heat sink and restrict airflow thereby reducing the cooling effectiveness and potentially leading to abnormal temperature rises.
This is absolutely critical in a machine environment where you've got dust, oil mist and all sorts of other contaminants.
3. Excessive Operating Load
Operating the power module under excessive load or under unsuitable operating conditions will increase the amount of heat generated.
Check the machine's operating conditions and compare the actual load against the specifications of the module that's been installed.
4. Internal Power Module Fault
If the cooling fan, heat sink and operating conditions are all normal but the alarm persists then an internal fault in the PSM or servo unit may require further investigation.
How to Troubleshoot FANUC Alarm 431 Step by Step
Step 1: Confirm the Alarm and Identify the Module
Firstly, confirm that the CNC is displaying 431 – CNV. OVERLOAD.
Record the CNC model and the power supply or servo unit (e.g. a PSM or beta series SVU) that's fitted. Check the module LED's and record any further alarm codes.
Different generations of FANUC modules will use different internal alarm codes so you'll need to refer to the maintenance manual for the particular model in question.
Step 2: Check the Cooling Fan
Just check the cooling fan is working OK.
Check for:
- Fan failure or abnormal rotation
- Unusual noise or mechanical obstruction
- Loose or damaged connectors
- Problems with the fan power connection
If the fan is faulty then replace it with a suitable unit in accordance with the relevant FANUC specifications.
Step 3: Inspect and Clean the Heat Sink
Check the heat sink, the air inlets and the cooling passages for dust or other contamination.
Clean the cooling system in accordance with the method recommended in the relevant FANUC manual. For the PSM models covered by manual B-65165E/02, FANUC specifies that the cooling system be cleaned using a vacuum cleaner or factory air blower.
Just make sure the airflow isn't obstructed after you've cleaned it.
Step 4: Check the Operating Load
If the cooling system is up to par, look at the machine's operating conditions.
Check whether the power module is being operated under an excessive load or outside its specified operating conditions. Check the machine's operating history and any available load data.
Correct any unsuitable operating conditions prior to replacing the module.
Step 5: Inspect the Power Supply or Servo Unit
If the alarm continues after you've checked the cooling system and the operating load then the module will probably need further testing.
A qualified technician should inspect the PSM or servo unit to see if there's an internal power circuit fault, a temperature monitoring component fault or some other module fault.
Just replace the module once the fault has been correctly diagnosed.
Step 6: Restore Operation and Verify the Result
Having completed the requisite repairs, restore power in accordance with the machine manufacturer's instructions.
Check the cooling fan is operating normally, the module temperature is in the correct range and Alarm 431 hasn't reappeared.
Common Mistakes When Fixing FANUC Alarm 431
Avoid these common troubleshooting mistakes:
- Confusing Alarm 430 with Alarm 431: Alarm 430 is a servo motor overheat alarm, Alarm 431 is a converter/power supply alarm.
- Faulty cooling fan or blocked heatsink could be the cause of the alarm - don't replace the PSM too early.
- Ignore the build up of dust: cleaning the cooling system is a key maintenance step.
- Overlooking the operating conditions: excessive load can result in overheating even if the cooling fan is working perfectly.
Always check the cooling system and operating conditions prior to concluding that the power module is defective.
Safety Precautions During Troubleshooting
Power supply and servo modules contain hazardous electrical voltages. Prior to inspecting connectors, cleaning the internal cooling areas or replacing any components, you must follow the machine's approved shutdown and electrical isolation procedures.
Residual voltage may remain in the module after the power has been switched off. Observe the discharge waiting time as specified in the relevant FANUC manual.
Electrical measurements and internal module repairs should only be carried out by qualified technicians using the appropriate equipment.
Should you repair or replace the FANUC power supply module?
The decision is down to actual fault.
If the fault is down to a defective cooling fan or build-up of dust then rectifying the cooling issue may well cure the alarm without the need to replace the whole module.
If the PSM or servo unit has an internal fault then professional testing is required to establish whether it can be repaired. If repair is not viable then a compatible replacement will be required.
When buying a replacement, make sure you have the full part number, the correct electrical specs and that it's compatible with your existing FANUC system. For used modules you'll also need to check the test status and the warranty.
How SongWei CNC Can Help
SongWei CNC supply new and used FANUC CNC spare parts. These include power supply modules (PSM), servo amplifiers, spindle amplifiers, motors and CNC circuit boards.
We also provide testing and repair of FANUC components to support machine maintenance and equipment recovery.
If you need help with FANUC Alarm 431 then please provide your CNC model, your power supply or servo unit model, the full alarm info and photos of the module label. That will enable us to get a proper understanding of what you have and what the likely replacement part(s) or repair solution is.
Conclusion
FANUC Alarm 431 (CNV. OVERLOAD) is an alarm indicating an overheat condition in the converter or power supply section (as applicable to FANUC systems).
Start by identifying the installed module, then inspect the cooling fan, heat sink, and operating conditions. If these checks do not resolve the alarm, arrange further testing of the PSM or servo unit.
Accurate diagnosis before replacing components can help reduce unnecessary costs and machine downtime.
